How To Fit Coving

Coving is a really nice detail to add to any room in your house and it comes in a variety of types to best suit your requirements. Within this article, we walk you through the steps required to fit coving yourself along with pictures of each step of the process.

Tweet Pin It
How To Fit Coving
Darimo is reader-supported and we may earn an affiliate commission if you buy through links on our site. Find out more.

Whether you are using coving to hide settlement cracks between the wall and ceiling or simply fitting it to give a room a bit more character, it’s a great finishing touch. The coving is available in a variety of styles and sizes as well as three different materials which include plaster, duropolymer and polystyrene.

Plaster coving is the most popular due to its durability but it does weigh quite a bit more than the alternatives, which means it requires additional effort to install. Duropolymer coving is similar to the plaster alternative but its lighter and easier to install. However, this type of coving does come at a premium cost for the added benefits. Finally, polystyrene coving is the cheapest and lightest but it has the drawback of being less durable and requiring additional decorating.

In this particular tutorial of how to fit coving, we are using the traditional plaster coving as shown below.

What You’ll Need

  • Plaster coving
  • Cove adhesive
  • Pencil/marker
  • Mitre box
  • Masonry pins
  • Hammer
  • Spirit level
  • Panel saw
  • Utility knife
  • Sander/sand paper
  • Filler

How To Fit Coving


1. Check The Fit Against The Wall & Ceiling

To begin fitting coving, we always recommend checking the fit against the wall and ceiling beforehand. You’ll need to take note of any lumps or bumps and it’s also a good time to decide if you actually like the coving. For example, we initially tested a 2 inch coving on the wall and ceiling but after checking the fit, we decided to go with a 3 inch coving instead.

2. Mark Out Where The Edges

Once you are happy with the coving you’ve bought, you can begin to mark out where the edges of the coving need to be when it’s fixed. You’ll need to follow the manufacturers guidance in terms of the markings because not all coving is the same. As you can see in the photo below, we used a pencil to make markings on both the wall and ceiling.

how to put up coving

3. Prepare The Area Before Fitting

After you’ve marked the area, you’ll need to check for any dust, dirt or grease because this can effect how the coving adheres to the surface. If you notice that it isn’t particularly clean, you will need to clean it prior to fitting the coving.

As you can see in the image above, we painted the fresh plaster prior to installing the coving. Therefore, to avoid any adhesion issues, we sanded down the area and also scored the wall for a better key for the adhesive.

how to fit plaster coving

4. Cut Any Internal or External Coving Angles

With all the preparation work complete, you can now concentrate on the coving itself. To begin, you’ll need to cut the ends ready to form the joints at the corner and this will be determined by the shape of the room.

The easiest way to accurately cut your coving is with the use of a mitre box. Depending upon whether you are cutting an external or internal corner on the right or left hand side will determine the direction of the saw cut that’s required.

Once you have marked out the length and angle to cut the coving, you can use a panel saw to cut through it. If you are cutting a long length of coving, make sure that the other side is supported because this avoids it from snapping. We also strongly recommend having a few practice runs of cutting the coving so that you’re happy when it comes to the real thing.

After you have cut the coving to length, you’ll need to check the fit upon the wall and ceiling. If you aren’t happy, place the coving back into the mitre box and make the adjustment. However, if it’s only a small amount of adjustment required, you can use a utility knife to make the cut instead.

how to cut coving

5. Mix Up Adhesive & Apply To Coving

When it comes to sticking the coving on, you’ll have a choice of products to use. Personally, we prefer to use a dedicated cove adhesive but other people have their own preferences such as dot and dab.

In terms of mixing up the cove adhesive, it varies between all the different types. For example, the adhesive we used required 5 litres of water per 12.5 KG bag. However, before mixing the adhesive, take note of the workable time once it has been mixed up. Most vary between 30 to 45 minutes, which means that you’ll want to ensure you have all the coving ready to make the most of the workable time. Alternatively, you can mix smaller portions of the adhesive rather than the whole bag.

With the cove adhesive mixed and ready to use, you can begin to spread it onto both sides of the coving. You will need to apply enough adhesive so that it squeezes out from the edges when the coving is pushed into position.

Cove Adhesive

6. Position Coving & Push In Position

With the back of the coving covered in adhesive on both sides, use the marking lines to position the coving ready to be stuck on. Once you are happy it’s in position, you can move along its length pushing it into place. When it comes to joining two lengths of coving, make sure you add plenty of adhesive to the mitre joint too so that it sticks in position.

how to put coving up

7. Fill Gaps Using The Adhesive

After pushing the coving into position, if you spot any gaps, simply fill them using the cove adhesive. Afterwards, use a slightly damp cloth to wipe down any adhesive left upon the surface so that it’s ready for decorating.

8. Pin The Coving In Position

Although not always necessary, you can pin the coving in place for added security whilst the adhesive sets. Ideally, you should hammer a masonry pin at every 60 cm interval along the coving. However, so that they can be removed, avoid hammering the pins in too far because this will make the removal a lot more harder than it needs to be.

9. Remove Pins & Check Coving

Once you are happy that the adhesive has completely set (as per the manufacturers guidelines), you can begin to remove the pins. To do this, use the back of a hammer to pull each pin out.

10. Start Decorating

After successfully fitting the coving, it’s advised that you allow at least 24 hours before you start decorating. Prior to painting, you may want to use a decorators filler to fill in the areas where pins were inserted into the coving. When it comes round to painting the coving, use a suitable primer and then paint using emulsion for the best finish.


What To Avoid

  • Fitting coving to an unprepared surface (i.e. painted walls/ceilings or uneven surfaces)
  • Using a blunt saw to make cuts
  • Decorating before allowing the adhesive to set
  • Mixing the adhesive before measuring and cutting the coving
  • Using an incorrectly mixed or expired adhesive

Conclusion

Fitting coving isn’t the most straightforward of tasks due to the cuts needed but as long as you use a mitre box, it’s fairly straightforward to do. Hopefully our guide on how to fit coving enables you to give it a go yourself. However, if you feel you need extra guidance, you can get in touch and we will provide our assistance where possible.

The Author Who Worked On This Article

author dan darimo

Dan Morgan

As a keen DIY’er, gardener and somebody that loves the latest tech, Dan is someone that brings years of experience in multiple trades. Since buying his first house, he has been obsessed with renovating properties and filling it with the latest products. This has led him down the road of testing hundreds of products and creating in-depth “how-to” and informative guides that offer his first-hand experience. Other interests include working on cars, keeping fit through sports or his home gym, caravanning and drinking great coffee.

If you would like to read more about Darimo and the authors, you can visit our about page. This goes into great detail regarding how we test products, create our guides and everything else.

Follow #DarimoUK

Copyright © 2021. All rights reserved.